NFSv4 Working Group D. Black Internet Draft EMC Corporation Expires: June 25, 2009 S. Fridella Intended Status: Proposed Standard EMC Corporation J. Glasgow Google December 22, 2008 pNFS Block/Volume Layout draft-ietf-nfsv4-pnfs-block-12.txt Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html This Internet-Draft will expire on June 25, 2009. Copyright Notice Copyright (c) 2008 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Black, et al. Standards Track [Page 1] Internet-Draft pNFS Block/Volume Layout December 2008 Abstract Parallel NFS (pNFS) extends NFSv4 to allow clients to directly access file data on the storage used by the NFSv4 server. This ability to bypass the server for data access can increase both performance and parallelism, but requires additional client functionality for data access, some of which is dependent on the class of storage used. The main pNFS operations draft specifies storage-class-independent extensions to NFS; this draft specifies the additional extensions (primarily data structures) for use of pNFS with block and volume based storage. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [RFC2119]. Table of Contents Copyright Notice..................................................1 1. Introduction...................................................4 1.1. General Definitions.......................................4 1.2. Code Components Licensing Notice..........................5 1.3. XDR Description...........................................5 2. Block Layout Description.......................................8 2.1. Background and Architecture...............................8 2.2. GETDEVICELIST and GETDEVICEINFO...........................9 2.2.1. Volume Identification................................9 2.2.2. Volume Topology.....................................11 2.2.3. GETDEVICELIST and GETDEVICEINFO deviceid4...........14 2.3. Data Structures: Extents and Extent Lists................14 2.3.1. Layout Requests and Extent Lists....................17 2.3.2. Layout Commits......................................18 2.3.3. Layout Returns......................................19 2.3.4. Client Copy-on-Write Processing.....................19 2.3.5. Extents are Permissions.............................21 2.3.6. End-of-file Processing..............................22 2.3.7. Layout Hints........................................23 2.3.8. Client Fencing......................................23 2.4. Crash Recovery Issues....................................25 2.5. Recalling resources: CB_RECALL_ANY.......................26 2.6. Transient and Permanent Errors...........................26 3. Security Considerations.......................................27 4. Conclusions...................................................29 5. IANA Considerations...........................................29 Black, et al. Standards Track [Page 2] Internet-Draft pNFS Block/Volume Layout December 2008 6. Acknowledgments...............................................29 7. References....................................................29 7.1. Normative References.....................................29 7.2. Informative References...................................30 Authors' Addresses...............................................30 Black, et al. Standards Track [Page 3] Internet-Draft pNFS Block/Volume Layout December 2008 1. Introduction Figure 1 shows the overall architecture of a Parallel NFS (pNFS) system: +-----------+ |+-----------+ +-----------+ ||+-----------+ | | ||| | NFSv4.1 + pNFS | | +|| Clients |<------------------------------>| Server | +| | | | +-----------+ | | ||| +-----------+ ||| | ||| | ||| Storage +-----------+ | ||| Protocol |+-----------+ | ||+----------------||+-----------+ Control | |+-----------------||| | Protocol| +------------------+|| Storage |------------+ +| Systems | +-----------+ Figure 1 pNFS Architecture The overall approach is that pNFS-enhanced clients obtain sufficient information from the server to enable them to access the underlying storage (on the Storage Systems) directly. See the pNFS portion of [NFSV4.1] for more details. This draft is concerned with access from pNFS clients to Storage Systems over storage protocols based on blocks and volumes, such as the SCSI protocol family (e.g., parallel SCSI, FCP for Fibre Channel, iSCSI, SAS, and FCoE). This class of storage is referred to as block/volume storage. While the Server to Storage System protocol, called the "Control Protocol", is not of concern for interoperability here, it will typically also be a block/volume protocol when clients use block/ volume protocols. 1.1. General Definitions The following definitions are provided for the purpose of providing an appropriate context for the reader. Byte Black, et al. Standards Track [Page 4] Internet-Draft pNFS Block/Volume Layout December 2008 This document defines a byte as an octet, i.e. a datum exactly 8 bits in length. Client The "client" is the entity that accesses the NFS server's resources. The client may be an application which contains the logic to access the NFS server directly. The client may also be the traditional operating system client that provides remote file system services for a set of applications. Server The "Server" is the entity responsible for coordinating client access to a set of file systems and is identified by a Server owner. 1.2. Code Components Licensing Notice The external data representation (XDR) description and scripts for extracting the XDR description are Code Components as described in Section 4 of "Legal Provisions Relating to IETF Documents" [LEGAL]. These Code Components are licensed according to the terms of Section 4 of "Legal Provisions Relating to IETF Documents". 1.3. XDR Description This document contains the XDR ([XDR]) description of the NFSv4.1 block layout protocol. The XDR description is embedded in this document in a way that makes it simple for the reader to extract into a ready to compile form. The reader can feed this document into the following shell script to produce the machine readable XDR description of the NFSv4.1 block layout: #!/bin/sh grep '^ *///' $* | sed 's?^ */// ??' | sed 's?^ *///$??' I.e. if the above script is stored in a file called "extract.sh", and this document is in a file called "spec.txt", then the reader can do: sh extract.sh < spec.txt > nfs4_block_layout_spec.x The effect of the script is to remove both leading white space and a sentinel sequence of "///" from each matching line. Black, et al. Standards Track [Page 5] Internet-Draft pNFS Block/Volume Layout December 2008 The embedded XDR file header follows, with subsequent pieces embedded throughout the document: Black, et al. Standards Track [Page 6] Internet-Draft pNFS Block/Volume Layout December 2008 /// /* /// * This code was derived from IETF RFC &rfc.number. [[RFC Editor: please insert RFC number if needed]] /// * Please reproduce this note if possible. /// */ /// /* /// * Copyright (c) 2008 IETF Trust and the persons identified /// * as the document authors. All rights reserved. /// * /// * Redistribution and use in source and binary forms, with /// * or without modification, are permitted provided that the /// * following conditions are met: /// * /// * o Redistributions of source code must retain the above /// * copyright notice, this list of conditions and the /// * following disclaimer. /// * /// * o Redistributions in binary form must reproduce the above /// * copyright notice, this list of conditions and the /// * following disclaimer in the documentation and/or other /// * materials provided with the distribution. /// * /// * o Neither the name of Internet Society, IETF or IETF /// * Trust, nor the names of specific contributors, may be /// * used to endorse or promote products derived from this /// * software without specific prior written permission. /// * /// * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS /// * AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED /// * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE /// * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS /// * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO /// * EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE /// * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, /// * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT /// * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR /// * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS /// * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF /// * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, /// * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING /// * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF /// * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. /// */ Black, et al. Standards Track [Page 7] Internet-Draft pNFS Block/Volume Layout December 2008 /// /// /* /// * nfs4_block_layout_prot.x /// */ /// /// %#include "nfsv41.h" /// The XDR code contained in this document depends on types from nfsv41.x file. This includes both nfs types that end with a 4, such as offset4, length4, etc, as well as more generic types such as uint32_t and uint64_t. 2. Block Layout Description 2.1. Background and Architecture The fundamental storage abstraction supported by block/volume storage is a storage volume consisting of a sequential series of fixed size blocks. This can be thought of as a logical disk; it may be realized by the Storage System as a physical disk, a portion of a physical disk or something more complex (e.g., concatenation, striping, RAID, and combinations thereof) involving multiple physical disks or portions thereof. A pNFS layout for this block/volume class of storage is responsible for mapping from an NFS file (or portion of a file) to the blocks of storage volumes that contain the file. The blocks are expressed as extents with 64 bit offsets and lengths using the existing NFSv4 offset4 and length4 types. Clients must be able to perform I/O to the block extents without affecting additional areas of storage (especially important for writes), therefore extents MUST be aligned to 512-byte boundaries, and writable extents MUST be aligned to the block size used by the NFSv4 server in managing the actual file system (4 kilobytes and 8 kilobytes are common block sizes). This block size is available as the NFSv4.1 layout_blksize attribute. [NFSV4.1]. Readable extents SHOULD be aligned to the block size used by the NFSv4 server, but in order to support legacy file systems with fragments, alignment to 512 byte boundaries is acceptable. The pNFS operation for requesting a layout (LAYOUTGET) includes the "layoutiomode4 loga_iomode" argument which indicates whether the requested layout is for read-only use or read-write use. A read-only layout may contain holes that are read as zero, whereas a read-write Black, et al. Standards Track [Page 8] Internet-Draft pNFS Block/Volume Layout December 2008 layout will contain allocated, but un-initialized storage in those holes (read as zero, can be written by client). This draft also supports client participation in copy on write (e.g. for file systems with snapshots) by providing both read-only and un-initialized storage for the same range in a layout. Reads are initially performed on the read-only storage, with writes going to the un- initialized storage. After the first write that initializes the un- initialized storage, all reads are performed to that now-initialized writeable storage, and the corresponding read-only storage is no longer used. The block/volume layout solution expands the security responsibilities of the pNFS clients and there are a number of environments where the mandatory to implement security properties for NFS cannot be satisfied. The additional security responsibilities of the client follow, and a full discussion is present in Section 3 "Security Considerations". o Typically, storage area network (SAN) disk arrays and SAN protocols provide access control mechanisms (e.g., logical unit number mapping and/or masking) which operate at the granularity of individual hosts, not individual blocks. For this reason, block- based protection must be provided by the client software. o Similarly, SAN disk arrays and SAN protocols typically are not be able to validate NFS locks that apply to file regions. For instance, if a file is covered by a mandatory read-only lock, the server can ensure that only readable layouts for the file are granted to pNFS clients. However, it is up to each pNFS client to ensure that the readable layout is used only to service read requests, and not to allow writes to the existing parts of the file. Since block/volume storage systems are generally not capable of enforcing such file-based security, in environments where pNFS clients cannot be trusted to enforce such policies, pNFS block/volume storage layouts SHOULD NOT be used. 2.2. GETDEVICELIST and GETDEVICEINFO 2.2.1. Volume Identification Storage Systems such as storage arrays can have multiple physical network ports that need not be connected to a common network, resulting in a pNFS client having simultaneous multipath access to the same storage volumes via different ports on different networks. Black, et al. Standards Track [Page 9] Internet-Draft pNFS Block/Volume Layout December 2008 The networks may not even be the same technology - for example, access to the same volume via both iSCSI and Fibre Channel is possible, hence network addresses are difficult to use for volume identification. For this reason, this pNFS block layout identifies storage volumes by content, for example providing the means to match (unique portions of) labels used by volume managers. Volume identification is performed by matching one or more opaque byte sequences to specific parts of the stored data. Any block pNFS system using this layout MUST support a means of content-based unique volume identification that can be employed via the data structure given here. /// struct pnfs_block_sig_component4 { /* disk signature component */ /// int64_t bsc_sig_offset; /* byte offset of component /// on volume*/ /// opaque bsc_contents<>; /* contents of this component /// of the signature */ /// }; /// Note that the opaque "bsc_contents" field in the "pnfs_block_sig_component4" structure MUST NOT be interpreted as a zero-terminated string, as it may contain embedded zero-valued bytes. There are no restrictions on alignment (e.g., neither bsc_sig_offset nor the length are required to be multiples of 4). The bsc_sig_offset is a signed quantity which when positive represents an byte offset from the start of the volume, and when negative represents an byte offset from the end of the volume. Negative offsets are permitted in order to simplify the client implementation on systems where the device label is found at a fixed offset from the end of the volume. If the server uses negative offsets to describe the signature, then the client and server MUST NOT see different volume sizes. Negative offsets SHOULD NOT be used in systems that dynamically resize volumes unless care is taken to ensure that the device label is always present at the offset from the end of the volume as seen by the clients. A signature is an array of up to "PNFS_BLOCK_MAX_SIG_COMP" (defined below) signature components. The client MUST NOT assume that all signature components are colocated within a single sector on a block device. Black, et al. Standards Track [Page 10] Internet-Draft pNFS Block/Volume Layout December 2008 The pNFS client block layout driver uses this volume identification to map pnfs_block_volume_type4 PNFS_BLOCK_VOLUME_SIMPLE deviceid4s to its local view of a logical unit number (LUN). 2.2.2. Volume Topology The pNFS block server volume topology is expressed as an arbitrary combination of base volume types enumerated in the following data structures. The individual components of the topology are contained in an array and components may refer to other components by using array indices. Black, et al. Standards Track [Page 11] Internet-Draft pNFS Block/Volume Layout December 2008 /// enum pnfs_block_volume_type4 { /// PNFS_BLOCK_VOLUME_SIMPLE = 0, /* volume maps to a single /// LU */ /// PNFS_BLOCK_VOLUME_SLICE = 1, /* volume is a slice of /// another volume */ /// PNFS_BLOCK_VOLUME_CONCAT = 2, /* volume is a /// concatenation of /// multiple volumes */ /// PNFS_BLOCK_VOLUME_STRIPE = 3 /* volume is striped across /// multiple volumes */ /// }; /// /// const PNFS_BLOCK_MAX_SIG_COMP = 16;/* maximum components per /// signature */ /// struct pnfs_block_simple_volume_info4 { /// pnfs_block_sig_component4 bsv_ds; /// /* disk signature */ /// }; /// /// /// struct pnfs_block_slice_volume_info4 { /// offset4 bsv_start; /* offset of the start of the /// slice in bytes */ /// length4 bsv_length; /* length of slice in bytes */ /// uint32_t bsv_volume; /* array index of sliced /// volume */ /// }; /// /// struct pnfs_block_concat_volume_info4 { /// uint32_t bcv_volumes<>; /* array indices of volumes /// which are concatenated */ /// }; /// /// struct pnfs_block_stripe_volume_info4 { /// length4 bsv_stripe_unit; /* size of stripe in bytes */ /// uint32_t bsv_volumes<>; /* array indices of volumes /// which are striped across -- /// MUST be same size */ /// }; /// Black, et al. Standards Track [Page 12] Internet-Draft pNFS Block/Volume Layout December 2008 /// union pnfs_block_volume4 switch (pnfs_block_volume_type4 type) { /// case PNFS_BLOCK_VOLUME_SIMPLE: /// pnfs_block_simple_volume_info4 bv_simple_info; /// case PNFS_BLOCK_VOLUME_SLICE: /// pnfs_block_slice_volume_info4 bv_slice_info; /// case PNFS_BLOCK_VOLUME_CONCAT: /// pnfs_block_concat_volume_info4 bv_concat_info; /// case PNFS_BLOCK_VOLUME_STRIPE: /// pnfs_block_stripe_volume_info4 bv_stripe_info; /// }; /// /// /* block layout specific type for da_addr_body */ /// struct pnfs_block_deviceaddr4 { /// pnfs_block_volume4 bda_volumes<>; /* array of volumes */ /// }; /// The "pnfs_block_deviceaddr4" data structure is a structure that allows arbitrarily complex nested volume structures to be encoded. The types of aggregations that are allowed are stripes, concatenations, and slices. Note that the volume topology expressed in the pnfs_block_deviceaddr4 data structure will always resolve to a set of pnfs_block_volume_type4 PNFS_BLOCK_VOLUME_SIMPLE. The array of volumes is ordered such that the root of the volume hierarchy is the last element of the array. Concat, slice and stripe volumes MUST refer to volumes defined by lower indexed elements of the array. The "pnfs_block_device_addr4" data structure is returned by the server as the storage-protocol-specific opaque field da_addr_body in the "device_addr4" structure by a successful GETDEVICEINFO operation. [NFSV4.1]. As noted above, all device_addr4 structures eventually resolve to a set of volumes of type PNFS_BLOCK_VOLUME_SIMPLE. These volumes are each uniquely identified by a set of signature components. Complicated volume hierarchies may be composed of dozens of volumes each with several signature components, thus the device address may require several kilobytes. The client SHOULD be prepared to allocate a large buffer to contain the result. In the case of the server returning NFS4ERR_TOOSMALL the client SHOULD allocate a buffer of at least gdir_mincount_bytes to contain the expected result and retry the GETDEVICEINFO request. Black, et al. Standards Track [Page 13] Internet-Draft pNFS Block/Volume Layout December 2008 2.2.3. GETDEVICELIST and GETDEVICEINFO deviceid4 The server in response to a GETDEVICELIST request typically will return a single "deviceid4" in the gdlr_deviceid_list array. This is because the deviceid4 when passed to GETDEVICEINFO will return a "device_addr4" which encodes the entire volume hierarchy. In the case of copy-on-write file systems, the "gdlr_deviceid_list" array may contain two deviceid4's, one referencing the read-only volume hierarchy, and one referencing the writable volume hierarchy. There is no required ordering of the readable and writable ids in the array as the volumes are uniquely identified by their deviceid4, and are referred to by layouts using the deviceid4. Another example of the server returning multiple device items occurs when the file handle represents the root of a name space spanning multiple physical file systems on the server, each with a different volume hierarchy. In this example a server implementation may return either a list of deviceids used by each of the physical file systems, or it may return an empty list. Each deviceid4 returned by a successful GETDEVICELIST operation is a shorthand id used to reference the whole volume topology. These device ids, as well as device ids return in extents of a LAYOUTGET operation, can be used as input to the GETDEVICEINFO operation. Decoding the "pnfs_block_deviceaddr4" results in a flat ordering of data blocks mapped to PNFS_BLOCK_VOLUME_SIMPLE volumes. Combined with the mapping to a client LUN described in 2.2.1 Volume Identification, a logical volume offset can be mapped to a block on a pNFS client LUN. [NFSV4.1] 2.3. Data Structures: Extents and Extent Lists A pNFS block layout is a list of extents within a flat array of data blocks in a logical volume. The details of the volume topology can be determined by using the GETDEVICEINFO operation (see discussion of volume identification, section 2.2 above). The block layout describes the individual block extents on the volume that make up the file. The offsets and length contained in an extent are specified in units of bytes. Black, et al. Standards Track [Page 14] Internet-Draft pNFS Block/Volume Layout December 2008 /// enum pnfs_block_extent_state4 { /// PNFS_BLOCK_READ_WRITE_DATA = 0,/* the data located by this /// extent is valid /// for reading and writing. */ /// PNFS_BLOCK_READ_DATA = 1, /* the data located by this /// extent is valid for reading /// only; it may not be /// written. */ /// PNFS_BLOCK_INVALID_DATA = 2, /* the location is valid; the /// data is invalid. It is a /// newly (pre-) allocated /// extent. There is physical /// space on the volume. */ /// PNFS_BLOCK_NONE_DATA = 3 /* the location is invalid. It /// is a hole in the file. /// There is no physical space /// on the volume. */ /// }; /// /// struct pnfs_block_extent4 { /// deviceid4 bex_vol_id; /* id of logical volume on /// which extent of file is /// stored. */ /// offset4 bex_file_offset; /* the starting byte offset in /// the file */ /// length4 bex_length; /* the size in bytes of the /// extent */ /// offset4 bex_storage_offset; /* the starting byte offset /// in the volume */ /// pnfs_block_extent_state4 bex_state; /// /* the state of this extent */ /// }; /// /// /* block layout specific type for loc_body */ /// struct pnfs_block_layout4 { /// pnfs_block_extent4 blo_extents<>; /// /* extents which make up this /// layout. */ /// }; /// The block layout consists of a list of extents which map the logical regions of the file to physical locations on a volume. The Black, et al. Standards Track [Page 15] Internet-Draft pNFS Block/Volume Layout December 2008 "bex_storage_offset" field within each extent identifies a location on the logical volume specified by the "bex_vol_id" field in the extent. The bex_vol_id itself is shorthand for the whole topology of the logical volume on which the file is stored. The client is responsible for translating this logical offset into an offset on the appropriate underlying SAN logical unit. In most cases all extents in a layout will reside on the same volume and thus have the same bex_vol_id. In the case of copy on write file systems, the PNFS_BLOCK_READ_DATA extents may have a different bex_vol_id from the writable extents. Each extent maps a logical region of the file onto a portion of the specified logical volume. The bex_file_offset, bex_length, and bex_state fields for an extent returned from the server are valid for all extents. In contrast, the interpretation of the bex_storage_offset field depends on the value of bex_state as follows (in increasing order): o PNFS_BLOCK_READ_WRITE_DATA means that bex_storage_offset is valid, and points to valid/initialized data that can be read and written. o PNFS_BLOCK_READ_DATA means that bex_storage_offset is valid and points to valid/ initialized data which can only be read. Write operations are prohibited; the client may need to request a read- write layout. o PNFS_BLOCK_INVALID_DATA means that bex_storage_offset is valid, but points to invalid un-initialized data. This data must not be physically read from the disk until it has been initialized. A read request for a PNFS_BLOCK_INVALID_DATA extent must fill the user buffer with zeros, unless the extent is covered by a PNFS_BLOCK_READ_DATA extent of a copy-on-write file system. Write requests must write whole server-sized blocks to the disk; bytes not initialized by the user must be set to zero. Any write to storage in a PNFS_BLOCK_INVALID_DATA extent changes the written portion of the extent to PNFS_BLOCK_READ_WRITE_DATA; the pNFS client is responsible for reporting this change via LAYOUTCOMMIT. o PNFS_BLOCK_NONE_DATA means that bex_storage_offset is not valid, and this extent may not be used to satisfy write requests. Read requests may be satisfied by zero-filling as for PNFS_BLOCK_INVALID_DATA. PNFS_BLOCK_NONE_DATA extents may be returned by requests for readable extents; they are never returned if the request was for a writeable extent. Black, et al. Standards Track [Page 16] Internet-Draft pNFS Block/Volume Layout December 2008 An extent list lists all relevant extents in increasing order of the bex_file_offset of each extent; any ties are broken by increasing order of the extent state (bex_state). 2.3.1. Layout Requests and Extent Lists Each request for a layout specifies at least three parameters: file offset, desired size, and minimum size. If the status of a request indicates success, the extent list returned must meet the following criteria: o A request for a readable (but not writeable) layout returns only PNFS_BLOCK_READ_DATA or PNFS_BLOCK_NONE_DATA extents (but not PNFS_BLOCK_INVALID_DATA or PNFS_BLOCK_READ_WRITE_DATA extents). o A request for a writeable layout returns PNFS_BLOCK_READ_WRITE_DATA or PNFS_BLOCK_INVALID_DATA extents (but not PNFS_BLOCK_NONE_DATA extents). It may also return PNFS_BLOCK_READ_DATA extents only when the offset ranges in those extents are also covered by PNFS_BLOCK_INVALID_DATA extents to permit writes. o The first extent in the list MUST contain the requested starting offset. o The total size of extents within the requested range MUST cover at least the minimum size. One exception is allowed: the total size MAY be smaller if only readable extents were requested and EOF is encountered. o Extents in the extent list MUST be logically contiguous for a read-only layout. For a read-write layout, the set of writable extents (i.e., excluding PNFS_BLOCK_READ_DATA extents) MUST be logically contiguous. Every PNFS_BLOCK_READ_DATA extent in a read-write layout MUST be covered by one or more PNFS_BLOCK_INVALID_DATA extents. This overlap of PNFS_BLOCK_READ_DATA and PNFS_BLOCK_INVALID_DATA extents is the only permitted extent overlap. o Extents MUST be ordered in the list by starting offset, with PNFS_BLOCK_READ_DATA extents preceding PNFS_BLOCK_INVALID_DATA extents in the case of equal bex_file_offsets. Black, et al. Standards Track [Page 17] Internet-Draft pNFS Block/Volume Layout December 2008 If the minimum requested size, loga_minlength, is zero, this is an indication to the metadata server that the client desires any layout at offset loga_offset or less that the metadata server has "readily available". Readily is subjective, and depends on the layout type and the pNFS server implementation. For block layout servers, readily available SHOULD be interpreted such that readable layouts are always available, even if some extents are in the PNFS_BLOCK_NONE_DATA state. When processing requests for writable layouts, a layout is readily available if extents can be returned in the PNFS_BLOCK_READ_WRITE_DATA state. 2.3.2. Layout Commits /// /* block layout specific type for lou_body */ /// struct pnfs_block_layoutupdate4 { /// pnfs_block_extent4 blu_commit_list<>; /// /* list of extents which /// * now contain valid data. /// */ /// }; /// The "pnfs_block_layoutupdate4" structure is used by the client as the block-protocol specific argument in a LAYOUTCOMMIT operation. The "blu_commit_list" field is an extent list covering regions of the file layout that were previously in the PNFS_BLOCK_INVALID_DATA state, but have been written by the client and should now be considered in the PNFS_BLOCK_READ_WRITE_DATA state. The bex_state field of each extent in the blu_commit_list MUST be set to PNFS_BLOCK_READ_WRITE_DATA. The extents in the commit list MUST be disjoint and MUST be sorted by bex_file_offset. The bex_storage_offset field is unused. Implementers should be aware that a server may be unable to commit regions at a granularity smaller than a file-system block (typically 4KB or 8KB). As noted above, the block-size that the server uses is available as an NFSv4 attribute, and any extents included in the "blu_commit_list" MUST be aligned to this granularity and have a size that is a multiple of this granularity. If the client believes that its actions have moved the end-of-file into the middle of a block being committed, the client MUST write zeroes from the end-of-file to the end of that block before committing the block. Failure to do so may result in junk (uninitialized data) appearing in that area if the file is subsequently extended by moving the end-of-file. Black, et al. Standards Track [Page 18] Internet-Draft pNFS Block/Volume Layout December 2008 2.3.3. Layout Returns The LAYOUTRETURN operation is done without any block layout specific data. When the LAYOUTRETURN operation specifies a LAYOUTRETURN4_FILE_return type, then the layoutreturn_file4 data structure specifies the region of the file layout that is no longer needed by the client. The opaque "lrf_body" field of the "layoutreturn_file4" data structure MUST have length zero. A LAYOUTRETURN operation represents an explicit release of resources by the client, usually done for the purpose of avoiding unnecessary CB_LAYOUTRECALL operations in the future. The client may return disjoint regions of the file by using multiple LAYOUTRETURN operations within a single COMPOUND operation. Note that the block/volume layout supports unilateral layout revocation. When a layout is unilaterally revoked by the server, usually due to the client's lease time expiring, or a delegation being recalled, or the client failing to return a layout in a timely manner, it is important for the sake of correctness that any in- flight I/Os that the client issued before the layout was revoked are rejected at the storage. For the block/volume protocol, this is possible by fencing a client with an expired layout timer from the physical storage. Note, however, that the granularity of this operation can only be at the host/logical-unit level. Thus, if one of a client's layouts is unilaterally revoked by the server, it will effectively render useless *all* of the client's layouts for files located on the storage units comprising the logical volume. This may render useless the client's layouts for files in other file systems. 2.3.4. Client Copy-on-Write Processing Copy-on-write is a mechanism used to support file and/or file system snapshots. When writing to unaligned regions, or to regions smaller than a file system block, the writer must copy the portions of the original file data to a new location on disk. This behavior can either be implemented on the client or the server. The paragraphs below describe how a pNFS block layout client implements access to a file which requires copy-on-write semantics. Distinguishing the PNFS_BLOCK_READ_WRITE_DATA and PNFS_BLOCK_READ_DATA extent types in combination with the allowed overlap of PNFS_BLOCK_READ_DATA extents with PNFS_BLOCK_INVALID_DATA extents allows copy-on-write processing to be done by pNFS clients. In classic NFS, this operation would be done by the server. Since pNFS enables clients to do direct block access, it is useful for Black, et al. Standards Track [Page 19] Internet-Draft pNFS Block/Volume Layout December 2008 clients to participate in copy-on-write operations. All block/volume pNFS clients MUST support this copy-on-write processing. When a client wishes to write data covered by a PNFS_BLOCK_READ_DATA extent, it MUST have requested a writable layout from the server; that layout will contain PNFS_BLOCK_INVALID_DATA extents to cover all the data ranges of that layout's PNFS_BLOCK_READ_DATA extents. More precisely, for any bex_file_offset range covered by one or more PNFS_BLOCK_READ_DATA extents in a writable layout, the server MUST include one or more PNFS_BLOCK_INVALID_DATA extents in the layout that cover the same bex_file_offset range. When performing a write to such an area of a layout, the client MUST effectively copy the data from the PNFS_BLOCK_READ_DATA extent for any partial blocks of bex_file_offset and range, merge in the changes to be written, and write the result to the PNFS_BLOCK_INVALID_DATA extent for the blocks for that bex_file_offset and range. That is, if entire blocks of data are to be overwritten by an operation, the corresponding PNFS_BLOCK_READ_DATA blocks need not be fetched, but any partial- block writes must be merged with data fetched via PNFS_BLOCK_READ_DATA extents before storing the result via PNFS_BLOCK_INVALID_DATA extents. For the purposes of this discussion, "entire blocks" and "partial blocks" refer to the server's file-system block size. Storing of data in a PNFS_BLOCK_INVALID_DATA extent converts the written portion of the PNFS_BLOCK_INVALID_DATA extent to a PNFS_BLOCK_READ_WRITE_DATA extent; all subsequent reads MUST be performed from this extent; the corresponding portion of the PNFS_BLOCK_READ_DATA extent MUST NOT be used after storing data in a PNFS_BLOCK_INVALID_DATA extent. If a client writes only a portion of an extent, the extent may be split at block aligned boundaries. When a client wishes to write data to a PNFS_BLOCK_INVALID_DATA extent that is not covered by a PNFS_BLOCK_READ_DATA extent, it MUST treat this write identically to a write to a file not involved with copy-on-write semantics. Thus, data must be written in at least block size increments, aligned to multiples of block sized offsets, and unwritten portions of blocks must be zero filled. In the LAYOUTCOMMIT operation that normally sends updated layout information back to the server, for writable data, some PNFS_BLOCK_INVALID_DATA extents may be committed as PNFS_BLOCK_READ_WRITE_DATA extents, signifying that the storage at the corresponding bex_storage_offset values has been stored into and is now to be considered as valid data to be read. PNFS_BLOCK_READ_DATA extents are not committed to the server. For extents that the client receives via LAYOUTGET as Black, et al. Standards Track [Page 20] Internet-Draft pNFS Block/Volume Layout December 2008 PNFS_BLOCK_INVALID_DATA and returns via LAYOUTCOMMIT as PNFS_BLOCK_READ_WRITE_DATA, the server will understand that the PNFS_BLOCK_READ_DATA mapping for that extent is no longer valid or necessary for that file. 2.3.5. Extents are Permissions Layout extents returned to pNFS clients grant permission to read or write; PNFS_BLOCK_READ_DATA and PNFS_BLOCK_NONE_DATA are read-only (PNFS_BLOCK_NONE_DATA reads as zeroes), PNFS_BLOCK_READ_WRITE_DATA and PNFS_BLOCK_INVALID_DATA are read/write, (PNFS_BLOCK_INVALID_DATA reads as zeros, any write converts it to PNFS_BLOCK_READ_WRITE_DATA). This is the only client means of obtaining permission to perform direct I/O to storage devices; a pNFS client MUST NOT perform direct I/O operations that are not permitted by an extent held by the client. Client adherence to this rule places the pNFS server in control of potentially conflicting storage device operations, enabling the server to determine what does conflict and how to avoid conflicts by granting and recalling extents to/from clients. Block/volume class storage devices are not required to perform read and write operations atomically. Overlapping concurrent read and write operations to the same data may cause the read to return a mixture of before-write and after-write data. Overlapping write operations can be worse, as the result could be a mixture of data from the two write operations; data corruption can occur if the underlying storage is striped and the operations complete in different orders on different stripes. A pNFS server can avoid these conflicts by implementing a single writer XOR multiple readers concurrency control policy when there are multiple clients who wish to access the same data. This policy MUST be implemented when storage devices do not provide atomicity for concurrent read/write and write/write operations to the same data. If a client makes a layout request that conflicts with an existing layout delegation, the request will be rejected with the error NFS4ERR_LAYOUTTRYLATER. This client is then expected to retry the request after a short interval. During this interval the server SHOULD recall the conflicting portion of the layout delegation from the client that currently holds it. This reject-and-retry approach does not prevent client starvation when there is contention for the layout of a particular file. For this reason a pNFS server SHOULD implement a mechanism to prevent starvation. One possibility is that the server can maintain a queue of rejected layout requests. Each new layout request can be checked to see if it conflicts with a previous rejected request, and if so, the newer request can be Black, et al. Standards Track [Page 21] Internet-Draft pNFS Block/Volume Layout December 2008 rejected. Once the original requesting client retries its request, its entry in the rejected request queue can be cleared, or the entry in the rejected request queue can be removed when it reaches a certain age. NFSv4 supports mandatory locks and share reservations. These are mechanisms that clients can use to restrict the set of I/O operations that are permissible to other clients. Since all I/O operations ultimately arrive at the NFSv4 server for processing, the server is in a position to enforce these restrictions. However, with pNFS layouts, I/Os will be issued from the clients that hold the layouts directly to the storage devices that host the data. These devices have no knowledge of files, mandatory locks, or share reservations, and are not in a position to enforce such restrictions. For this reason the NFSv4 server MUST NOT grant layouts that conflict with mandatory locks or share reservations. Further, if a conflicting mandatory lock request or a conflicting open request arrives at the server, the server MUST recall the part of the layout in conflict with the request before granting the request. 2.3.6. End-of-file Processing The end-of-file location can be changed in two ways: implicitly as the result of a WRITE or LAYOUTCOMMIT beyond the current end-of-file, or explicitly as the result of a SETATTR request. Typically, when a file is truncated by an NFSv4 client via the SETATTR call, the server frees any disk blocks belonging to the file which are beyond the new end-of-file byte, and MUST write zeros to the portion of the new end- of-file block beyond the new end-of-file byte. These actions render any pNFS layouts which refer to the blocks that are freed or written semantically invalid. Therefore, the server MUST recall from clients the portions of any pNFS layouts which refer to blocks that will be freed or written by the server before processing the truncate request. These recalls may take time to complete; as explained in [NFSv4.1], if the server cannot respond to the client SETATTR request in a reasonable amount of time, it SHOULD reply to the client with the error NFS4ERR_DELAY. Blocks in the PNFS_BLOCK_INVALID_DATA state which lie beyond the new end-of-file block present a special case. The server has reserved these blocks for use by a pNFS client with a writable layout for the file, but the client has yet to commit the blocks, and they are not yet a part of the file mapping on disk. The server MAY free these blocks while processing the SETATTR request. If so, the server MUST recall any layouts from pNFS clients which refer to the blocks before processing the truncate. If the server does not free the Black, et al. Standards Track [Page 22] Internet-Draft pNFS Block/Volume Layout December 2008 PNFS_BLOCK_INVALID_DATA blocks while processing the SETATTR request, it need not recall layouts which refer only to the PNFS_BLOCK_INVALID DATA blocks. When a file is extended implicitly by a WRITE or LAYOUTCOMMIT beyond the current end-of-file, or extended explicitly by a SETATTR request, the server need not recall any portions of any pNFS layouts. 2.3.7. Layout Hints The SETATTR operation supports a layout hint attribute [NFSv4.1]. When the client sets a layout hint (data type layouthint4) with a layout type of LAYOUT4_BLOCK_VOLUME (the loh_type field), the loh_body field contains a value of data type pnfs_block_layouthint4. /// /* block layout specific type for loh_body */ /// struct pnfs_block_layouthint4 { /// uint64_t blh_maximum_io_time; /* maximum i/o time in seconds /// */ /// }; /// The block layout client uses the layout hint data structure to communicate to the server the maximum time that it may take an I/O to execute on the client. Clients using block layouts MUST set the layout hint attribute before using LAYOUTGET operations. 2.3.8. Client Fencing The pNFS block protocol must handle situations in which a system failure, typically a network connectivity issue, requires the server to unilaterally revoke extents from one client in order to transfer the extents to another client. The pNFS server implementation MUST ensure that when resources are transferred to another client, they are not used by the client originally owning them, and this must be ensured against any possible combination of partitions and delays among all of the participants to the protocol (server, storage and client). Two approaches to guaranteeing this isolation are possible and are discussed below. One implementation choice for fencing the block client from the block storage is the use of LUN masking or mapping at the storage systems or storage area network to disable access by the client to be isolated. This requires server access to a management interface for the storage system and authorization to perform LUN masking and Black, et al. Standards Track [Page 23] Internet-Draft pNFS Block/Volume Layout December 2008 management operations. For example, SMI-S [SMIS] provides a means to discover and mask LUNs, including a means of associating clients with the necessary World Wide Names or Initiator names to be masked. In the absence of support for LUN masking, the server has to rely on the clients to implement a timed lease I/O fencing mechanism. Because clients do not know if the server is using LUN masking, in all cases the client MUST implement timed lease fencing. In timed lease fencing we define two time periods, the first, "lease_time" is the length of a lease as defined by the server's lease_time attribute (see [NFSV4.1]), and the second, "blh_maximum_io_time" is the maximum time it can take for a client I/O to the storage system to either complete or fail; this value is often 30 seconds or 60 seconds, but may be longer in some environments. If the maximum client I/O time cannot be bounded, the client MUST use a value of all 1s as the blh_maximum_io_time. The client MUST use SETATTR with a layout hint of type LAYOUT4_BLOCK_VOLUME to inform the server of its maximum I/O time prior to issuing the first LAYOUTGET operation. The maximum io time hint is a per client attribute, and as such the server SHOULD maintain the value set by each client. A server which implements fencing via LUN masking SHOULD accept any maximum io time value from a client. A server which does not implement fencing may return an error NFS4ERR_INVAL to the SETATTR operation. Such a server SHOULD return NFS4ERR_INVAL when a client sends an unbounded maximum I/O time (all 1s), or when the maximum I/O time is significantly greater than that of other clients using block layouts with pNFS. When a client receives the error NFS4ERR_INVAL in response to the SETATTR operation for a layout hint, the client MUST NOT use the LAYOUTGET operation. After responding with NFS4ERR_INVAL to the SETATTR for layout hint, the server MUST return the error NFS4ERR_LAYOUTUNAVAILABLE to all subsequent LAYOUTGET operations from that client. Thus the server, by returning either NFS4ERR_INVAL or NFS4_OK determines whether or not a client with a large, or an unbounded maximum I/O time may use pNFS. Using the lease time and the maximum i/o time values, we specify the behavior of the client and server as follows. When a client receives layout information via a LAYOUTGET operation, those layouts are valid for at most "lease_time" seconds from when the server granted them. A layout is renewed by any successful SEQUENCE operation, or whenever a new stateid is created or updated (see the section "Lease Renewal" of [NFSV4.1]). If the layout lease Black, et al. Standards Track [Page 24] Internet-Draft pNFS Block/Volume Layout December 2008 is not renewed prior to expiration, the client MUST cease to use the layout after "lease_time" seconds from when it either sent the original LAYOUTGET command, or sent the last operation renewing the lease. In other words, the client may not issue any I/O to blocks specified by an expired layout. In the presence of large communication delays between the client and server it is even possible for the lease to expire prior to the server response arriving at the client. In such a situation the client MUST NOT use the expired layouts, and SHOULD revert to using standard NFSv41 READ and WRITE operations. Furthermore, the client must be configured such that I/O operations complete within the "blh_maximum_io_time" even in the presence of multipath drivers that will retry I/Os via multiple paths. As stated in the section "Dealing with Lease Expiration on the Client" of [NFSV4.1], if any SEQUENCE operation is successful, but sr_status_flag has SEQ4_STATUS_EXPIRED_ALL_STATE_REVOKED, SEQ4_STATUS_EXPIRED_SOME_STATE_REVOKED, or SEQ4_STATUS_ADMIN_STATE_REVOKED set, the client MUST immediately cease to use all layouts and device id to device address mappings associated with the corresponding server. In the absence of known two way communication between the client and the server on the fore channel, the server must wait for at least the time period "lease_time" plus "blh_maximum_io_time" before transferring layouts from the original client to any other client. The server, like the client, must take a conservative approach, and start the lease expiration timer from the time that it received the operation which last renewed the lease. 2.4. Crash Recovery Issues A critical requirement in crash recovery is that both the client and the server know when the other has failed. Additionally, it is required that a client sees a consistent view of data across server restarts. These requirements and a full discussion of crash recovery issues are covered in the "Crash Recovery" section of the NFSv41 specification [NFSV4.1]. This document contains additional crash recovery material specific only to the block/volume layout. When the server crashes while the client holds a writable layout, and the client has written data to blocks covered by the layout, and the blocks are still in the PNFS_BLOCK_INVALID_DATA state, the client has two options for recovery. If the data that has been written to these blocks is still cached by the client, the client can simply re-write the data via NFSv4, once the server has come back online. However, Black, et al. Standards Track [Page 25] Internet-Draft pNFS Block/Volume Layout December 2008 if the data is no longer in the client's cache, the client MUST NOT attempt to source the data from the data servers. Instead, it should attempt to commit the blocks in question to the server during the server's recovery grace period, by sending a LAYOUTCOMMIT with the "loca_reclaim" flag set to true. This process is described in detail in [NFSv4.1] section 18.42.4. 2.5. Recalling resources: CB_RECALL_ANY The server may decide that it cannot hold all of the state for layouts without running out of resources. In such a case, it is free to recall individual layouts using CB_LAYOUTRECALL to reduce the load, or it may choose to request that the client return any layout. The NFSv4.1 spec [NFSv4.1] defines the following types: const RCA4_TYPE_MASK_BLK_LAYOUT = 4; struct CB_RECALL_ANY4args { uint32_t craa_objects_to_keep; bitmap4 craa_type_mask; }; When the server sends a CB_RECALL_ANY request to a client specifying the RCA4_TYPE_MASK_BLK_LAYOUT bit in craa_type_mask, the client should immediately respond with NFS4_OK, and then asynchronously return complete file layouts until the number of files with layouts cached on the client is less than craa_object_to_keep. 2.6. Transient and Permanent Errors The server may respond to LAYOUTGET with a variety of error statuses. These errors can convey transient conditions or more permanent conditions that are unlikely to be resolved soon. The transient errors, NFS4ERR_RECALLCONFLICT and NFS4ERR_TRYLATER are used to indicate that the server cannot immediately grant the layout to the client. In the former case this is because the server has recently issued a CB_LAYOUTRECALL to the requesting client, whereas in the case of NFS4ERR_TRYLATER, the server cannot grant the request possibly due to sharing conflicts with other clients. In either case, a reasonable approach for the client is to wait several milliseconds and retry the request. The client SHOULD track the number of retries, and if forward progress is not made, the client SHOULD send the READ or WRITE operation directly to the server. Black, et al. Standards Track [Page 26] Internet-Draft pNFS Block/Volume Layout December 2008 The error NFS4ERR_LAYOUTUNAVAILABLE may be returned by the server if layouts are not supported for the requested file or its containing file system. The server may also return this error code if the server is the progress of migrating the file from secondary storage, or for any other reason which causes the server to be unable to supply the layout. As a result of receiving NFS4ERR_LAYOUTUNAVAILABLE, the client SHOULD send future READ and WRITE requests directly to the server. It is expected that a client will not cache the file's layoutunavailable state forever, particular if the file is closed, and thus eventually, the client MAY reissue a LAYOUTGET operation. 3. Security Considerations Typically, SAN disk arrays and SAN protocols provide access control mechanisms (e.g., logical unit number mapping and/or masking) which operate at the granularity of individual hosts. The functionality provided by such mechanisms makes it possible for the server to "fence" individual client machines from certain physical disks---that is to say, to prevent individual client machines from reading or writing to certain physical disks. Finer-grained access control methods are not generally available. For this reason, certain security responsibilities are delegated to pNFS clients for block/volume layouts. Block/volume storage systems generally control access at a volume granularity, and hence pNFS clients have to be trusted to only perform accesses allowed by the layout extents they currently hold (e.g., and not access storage for files on which a layout extent is not held). In general, the server will not be able to prevent a client which holds a layout for a file from accessing parts of the physical disk not covered by the layout. Similarly, the server will not be able to prevent a client from accessing blocks covered by a layout that it has already returned. This block-based level of protection must be provided by the client software. An alternative method of block/volume protocol use is for the storage devices to export virtualized block addresses, which do reflect the files to which blocks belong. These virtual block addresses are exported to pNFS clients via layouts. This allows the storage device to make appropriate access checks, while mapping virtual block addresses to physical block addresses. In environments where the security requirements are such that client-side protection from access to storage outside of the authorized layout extents is not sufficient, pNFS block/volume storage layouts SHOULD NOT be used unless the storage device is able to implement the appropriate access checks, via use of virtualized block addresses or other means. In contrast, an environment where client-side protection may suffice Black, et al. Standards Track [Page 27] Internet-Draft pNFS Block/Volume Layout December 2008 consists of co-located clients, server and storage systems in a datacenter with a physically isolated SAN under control of a single system administrator or small group of system administrators. This also has implications for some NFSv4 functionality outside pNFS. For instance, if a file is covered by a mandatory read-only lock, the server can ensure that only readable layouts for the file are granted to pNFS clients. However, it is up to each pNFS client to ensure that the readable layout is used only to service read requests, and not to allow writes to the existing parts of the file. Similarly, block/volume storage devices are unable to validate NFS Access Control Lists (ACLs) and file open modes, so the client must enforce the policies before sending a read or write request to the storage device. Since block/volume storage systems are generally not capable of enforcing such file-based security, in environments where pNFS clients cannot be trusted to enforce such policies, pNFS block/volume storage layouts SHOULD NOT be used. Access to block/volume storage is logically at a lower layer of the I/O stack than NFSv4, and hence NFSv4 security is not directly applicable to protocols that access such storage directly. Depending on the protocol, some of the security mechanisms provided by NFSv4 (e.g., encryption, cryptographic integrity) may not be available, or may be provided via different means. At one extreme, pNFS with block/volume storage can be used with storage access protocols (e.g., parallel SCSI) that provide essentially no security functionality. At the other extreme, pNFS may be used with storage protocols such as iSCSI that can provide significant security functionality. It is the responsibility of those administering and deploying pNFS with a block/volume storage access protocol to ensure that appropriate protection is provided to that protocol (physical security is a common means for protocols not based on IP). In environments where the security requirements for the storage protocol cannot be met, pNFS block/volume storage layouts SHOULD NOT be used. When security is available for a storage protocol, it is generally at a different granularity and with a different notion of identity than NFSv4 (e.g., NFSv4 controls user access to files, iSCSI controls initiator access to volumes). The responsibility for enforcing appropriate correspondences between these security layers is placed upon the pNFS client. As with the issues in the first paragraph of this section, in environments where the security requirements are such that client-side protection from access to storage outside of the layout is not sufficient, pNFS block/volume storage layouts SHOULD NOT be used. Black, et al. Standards Track [Page 28] Internet-Draft pNFS Block/Volume Layout December 2008 4. Conclusions This draft specifies the block/volume layout type for pNFS and associated functionality. 5. IANA Considerations There are no IANA considerations in this document. All pNFS IANA Considerations are covered in [NFSV4.1]. 6. Acknowledgments This draft draws extensively on the authors' familiarity with the mapping functionality and protocol in EMC's MPFS (previously named HighRoad) system [MPFS]. The protocol used by MPFS is called FMP (File Mapping Protocol); it is an add-on protocol that runs in parallel with file system protocols such as NFSv3 to provide pNFS- like functionality for block/volume storage. While drawing on FMP, the data structures and functional considerations in this draft differ in significant ways, based on lessons learned and the opportunity to take advantage of NFSv4 features such as COMPOUND operations. The design to support pNFS client participation in copy- on-write is based on text and ideas contributed by Craig Everhart. Andy Adamson, Ben Campbell, Richard Chandler, Benny Halevy, Fredric Isaman, and Mario Wurzl all helped to review drafts of this specification. 7. References 7.1. Normative References [LEGAL] IETF Trust, "Legal Provisions Relating to IETF Documents", URL http://trustee.ietf.org/docs/IETF-Trust-License- Policy.pdf, November 2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [NFSV4.1] Shepler, S., Eisler, M., and Noveck, D. ed., "NFSv4 Minor Version 1", RFC [[RFC Editor: please insert NFSv4 Minor Version 1 RFC number]], [[RFC Editor: please insert NFSv4 Minor Version 1 RFC month]] [[RFC Editor: please insert NFSv4 Minor Version 1 year]. . Black, et al. Standards Track [Page 29] Internet-Draft pNFS Block/Volume Layout December 2008 [XDR] Eisler, M., "XDR: External Data Representation Standard", STD 67, RFC 4506, May 2006. 7.2. Informative References [MPFS] EMC Corporation, "EMC Celerra Multi-Path File System", EMC Data Sheet, available at: http://www.emc.com/collateral/software/data-sheet/h2006-celerra-mpfs- mpfsi.pdf link checked 13 March 2008 [SMIS] SNIA, "SNIA Storage Management Initiative Specification", version 1.0.2, available at: http://www.snia.org/tech_activities/standards/curr_standards/smi/SMI- S_Technical_Position_v1.0.3r1.pdf link checked 13 March 2008 Authors' Addresses David L. Black EMC Corporation 176 South Street Hopkinton, MA 01748 Phone: +1 (508) 293-7953 Email: black_david@emc.com Stephen Fridella EMC Corporation 228 South Street Hopkinton, MA 01748 Phone: +1 (508) 249-3528 Email: fridella_stephen@emc.com Jason Glasgow Google 5 Cambridge Center Cambridge, MA 02142 Phone: +1 (617) 575 1599 Email: jglasgow@aya.yale.edu Black, et al. Standards Track [Page 30]